Chassis: MR-04Hi-Quality steel ball bearing.ID3×OD6×W2.5(mm) --- 7pcs..

Chassis: MA-020, MA-030/EVO2, MA-03FThe increased toe angle allows for a more extreme setup. If additional angles are not required, we recommend the "+" angle tie rod in the KYOSHO parts kit.More detail for MA-020: KYOSHO MDW203 ↗More detail for MA-030/EVO2/F: KYOSHO MDW303 ↗Compatible with KYOSHO lower plastic plate and MPower Alum. alloy Front Lower Wishbone Set.There are 1 degree and 2 degree options...

Chassis: Any chassis with DWS installed.NOTE! Your car must have KYOSHO DWS before it can be modified with this part.For detailed purchasing instructions, please refer to the DWS Parts Buying Guide ↗.More angles for adjustment. Lighter! almost half the weight of the original metal mods...

Standard M2×P0.4 thread.Tapping tips:First drill a 1.6mm diameter hole at the position to be tapped. Then tap the thread.If encounter a hole that is difficult to tap (such as a hard material), please tap a few threads and then back a little and then continue to tap, repeatedly and slowly to complete it. If necessary, you can apply lubricant to the hole being tapped...

Fit to: MRP004???..

Chassis: MA-020, MA-030/EVO2, MA-03FThe increased toe angle allows for a more extreme setup. If additional angles are not required, we recommend the "+" angle tie rod in the KYOSHO parts kit.More detail for MA-020: KYOSHO MDW203 ↗More detail for MA-030/EVO2/F: KYOSHO MDW303 ↗Compatible with KYOSHO lower plastic plate and MPower Alum. alloy Front Lower Wishbone Set.There are 1 degree and 2 degree options...

Chassis: Any chassis with DWS installed.NOTE! Your car must have KYOSHO DWS before it can be modified with this part.For detailed purchasing instructions, please refer to the DWS Parts Buying Guide ↗.An extra pair of special-sized shaft pins for user-customize to solve the problem of different inner diameters of different brands of Rear Hub. (Such as original plastic Rear Hub and R246 aluminum alloy Rear Hub.)More stronger lower arm, make the actions clearly. Reduce the problem of deformation...

Mainboard: EVO2The wire is thin and has moderate hardness and is easy to bend to shape and arrange the wiring.Three colors are available to match the KYOSHO motor...

Chassis: RWD (MR-03/MR-04)(For RWD (MR-03/MR-04) front springs to fine-tune front ride height.)ID3.4 × OD4.6 × H0.2 mm --- 8pcs..

Chassis: MR-03For MR-03 MM/LM variant...

Chassis: MA-030/EVO2, MA-03FThe separate design is conducive to the convenience of changing gear ratios.Compatible with original plastic arm and MPower-Pro Alum. alloy Arm.Make front upper portion stronger. Reduce the problem of it's often deformation...

Chassis: MA-030/EVO2, MA-03FReduce interference with the body, allowing more bodys to be used.Supports motors for Mini-Z from almost all brands, including those with screw holes for fixing and those without.Dedicated brace set included...

Chassis: Any chassis with DWS installed.NOTE! Your car must have KYOSHO DWS before it can be modified with this part.If you want to change to wide setting without KYOSHO Rear Long Sus.Arm Set (MDW100-07), you need Long Linker ↗.For detailed purchasing instructions, please refer to the DWS Parts Buying Guide ↗.Stepless fine tuning for camber angle.Strengthen the fixed.Compatible with MA-020, MA-030/EVO2, MA-03F.CAUTION!If you are using the DWS on the MA-030/EVO2, please take note of the following instructions:Based on original design by KYOSHO, the 90mm wheelbase is not compatible with DWS.Additionally, there is a risk of damaging the mainboard with the 94mm wheelbase. If you intend to use DWS with the 94mm wheelbase, it is recommended to manually modify the chassis to move the mainboard forward.98mm or longer wheelbase are no problem...

For Audi R8 LMS(Not compatible with versions after 2019. If you can trim it, it can be used after slightly trimming.)..